[Q19-Q43] Attested HPE0-S60 Dumps PDF Resource [2023] : Free Exams Dumps Materials : http://exams.dumpsmaterials.com

NO.19 An HPE Synergy customer needs to prevent a timeout and loss of communication during an external switch firmware upgrade.
Click the parameter that the customer should configure within an uplink set to meet this requirement

NO.20 Your customer has an HPE Synergy frame equipped with a D3940 Storage Module. Each of the compute nodes has an appropriate storage controller Installed and two 12Gb SAS switches installed in the first fabric.
The customer reports that compute nodes cannot access the storage module. What should you verify first when troubleshooting this problem?

If the D3940 module is imported in managed state that allows volume provisioning.

If there Is a logical interconnect created based on the 12Gb SAS switches.

If the D3940 storage module is property licensed through HPE OneView interface.

If there is at least one ISCSI network configured that will provide access to the module.

NO.21 Your customer is implementing an HPE Synergy solution based on three frames.
Click each of the ports that can be used to connect satellite modules.

NO.22 Which statement about HPE OneView milestone releases is true?

A milestone release is a release which must be installed on HPE Composer to support current version of the Service Pack for Synergy

A milestone release is a release that is published when HPE releases new hardware components to immediately support new systems

A milestone release is available for selected partners that give access to HPE OneView features which are not officially announced.

A milestone release is a release with an enhanced update architecture mat is a prerequisite prior to updating to a subsequent release.

NO.23 Your customer wants to add a second HPE Synergy frame to an existing logical enclosure Based on a single HPE Synergy frame. The customer wants to use a highly available master setup.
Which procedures should De performed during the expansion process? (Select two.)

Create a new logical interconnect group and enclosure group for two frames setup

Create a new logical enclosure based on both HPE Synergy frames.

Re-parent an existing enclosure group to the new logical interconnect group.

Modify an existing logical interconnect to include second HPE Synergy frame.

Move one of the master modules to the appropriate interconnect bay in the second frame.

NO.24 Match HPE Superdome Flex system with its specific feature.

NO.25 Refer to the exhibit.

Which statement about this logical JBOD is true?

This logical JBOD can be connected to multiple systems to formulate a snared datastore.

After deleting this logical JBOD drives will he blocked for 12h m case this JBOD must be re-created

After deleting this logical JBOD, its drives w not be available until a clean-up procedure 6 done

This logical JBOD can be presented to the compute nodes in a different frame.

NO.26 Your customer plans to manage HPE Primera using HPE Oneview
Which storage management tasks can be completed using HPE OneView for this environment?

CPG management

Volume provisioning

Cache management

Replication setup

NO.27 Which HPE Virtual Connect feature allows an administrator to suppress excessive inbound multicast broadcast and destination lookup failure (OLF) packets?

Pause flood protection

Loop protection

LLDP tagging

Storm control

NO.28 Your customer has a logical enclosure configured using a angle HPE Synergy frame with the following configuration
– two HPE Virtual Connect SE 100Gb F32 Modules for Synergy
– two HPE Synergy Virtual Connect SE 32Gb FC Modules -12 HPE Synergy 480 Gen10 Plus compute nodes with appropriate mezzanine cards They plan to add a new HPE Synergy frame to an existing logical enclosure with the following configuration
– two HPE Synergy Virtual Connect SE 32Gb FC Modules
– two HPE Synergy 20Gb interconnect Link Modules
– Eight HPE Synergy 480 Gen 10 Plus compute nodes with appropriate mezzanine cards Which statement about the planned configuration change is true?

Four compute modules must be moved to the second frame to balance the configuration

The two HPE Synergy 20Gb interconnect Link Modules must be replace with the 50Gb option

A license for an extended logical enclosure must be added to HPE OneView through GUI

The HPE Synergy virtual Connect SE 32Gb FC Modules from both frames should be stacked

NO.29 Refer to the exhibit.

Which statement about this logical interconnect group is true?

The master modules are located in the interconnect bays 2 and 5

For the given downlink speed, the maximum number of frames is reached

Both master modules are located in the same HPE S ynergy frame

To use interconnect bay set 3, all compute nodes must be half-height

NO.30 Your customer reports that they cannot deploy HPE Synergy compute nodes using HPE OneView for VMware vCenter Server (HPE OV4VC).
What should you check during troubleshooting process?

If HPE OneView credentials are added in vCenter Server

If an compute nodes are added to the vCenter Server

If the HPE Oneview instance Is integrated with HPE OV4VC.

If vCenter Server is licensed in the HPE Oneview interface

NO.31 Which statement about an HPE Oneview support dump is true?

Appliance support dump by default contains a logical enclosure support dump

Support dump is a binary file that can be opened only in a dedicated application

Support dump can be created if HPE Virtual Connect modules are installed in the frame

Preview support dump is available only when creating an appliance support dump

NO.32 After deploying HPE Superdome Flex 280 you need to check Core Analysis Engine (CAE) Log.
Click the appropriate section in the HPE Superdome Flex 280 management interface that will allow you to complete this task.

NO.33 Your customer added a new Ethernet network in HPE Oneview mat is used to manage their HPE Synergy platform.
When the customer tries to connect one of the compute nodes to this network through the server profile, this network is not available.
What must be done to fix this issue?

Check the Logical Enclosure settings and verify if the maximum number of networks allowed for this LE is reached.

To make this network available to use in the server profile, the customer must enable the Smart Link feature within network definition.

The newly created network must be added to the uplink set within the LIG, and Logical interconnect configuration must be updated from the LIG.

Check within the server profile which server hardware is used and perform the Refresh operation on this compute node to get the latest adapter information.

NO.34 Click the option that will allow you to change the ESXI image used In an OS Deployment Plan.

NO.35 Which statement about login redistribution is true?

NO.36 Match HPE SimpliVity team with the definition.

NO.37 Your customer uses HPE OneView to manage their HPE Synergy environment. They plan to use it to manage a new set equipment that includes.
– 20 HPE ProLiant DL365 Gen10 Plus servers
– 20 HPE ProLiant DL380 Gen10 Plus servers
– 5 HPE Primera 650
– 5 HPE MSA 2062 Storage Array
Which statements about now OneView will work with this new equipment are true? (Select two)

HPE ProLiant DL365 Gen10 Plus servers are not supported in HPE OneView

HPE MSA 2062 Storage Array is not supported in HPE OneView

HPE OneView replaces array management tools for both types of array

HPE ProLiant DL380 Gen10 Plus servers have an HPE OneView license included

HPE Primera 650 can be managed using HPE OneView.

NO.38 Refer to the exhibit.

Which statement about this logical interconnect group is true?

Both modules are located in different frames for redundancy

For an uplink set, ports from different modules can be selected

interconnect modules are installed in interconnect bays 1 and 4

An additional license is required to change the enclosure count

NO.39 Your customer wants to add dedicated Fibre Channel connectivity to the HPE Synergy frame running HPE Synergy 480 Gen10 compute modules, each with one CPU socket populated Currently they use two 12 Gb SAS switches and two HPE Virtual Connect SE 100Gb F32 Modules for HPE Synergy installed in third fabric.
What must be done to enable dedicated FC connectivity for this HPE Synergy frame?

A second CPU must be installed for all HPE Synergy 480 Gen10 compute nodes.

For Brocade switches, a logical interconnect group must be created in HPE OneView.

For VC-FC modules, all of server facing ports must be property licensed.

SAS switches must be moved to second fabric and FC modules Installed in the first one.

NO.40 Your customer plans to deploy VMware ESXi 7 0 U2 and they are looking for a hardware platform mat wilt allow them to use up to 24 TB of physical memory.
Which HPE compute system meets this customer’s requirements?

HPE ProLiant DL380 Gen 10 Plus

HPE Synergy 480 Gen10 Plus

HPE ProLiant DL560 Gen10

HPE Superdome Flex 280

NO.41 Your customer plans to deploy ESXi systems to HPE Synergy and HPE ProLiant servers using HPE OneView for VMware vCenter Server.
Which statement about HPE OneView for VMware vCenter Server functionality is true for this environment?

HPE ProLiant servers need an HPE OneView for VMware vCenter Server license for full functionality

Individual systems can be added to HPE OneView for VMware vCenter Server through an ILO management processor

HPE Synergy requires HPE Composer 2 for full functionality of HPE OneView for VMware vCenter Server

Only systems managed using HPE Oneview can use HPE Oneview for VMware vCenter Server functionalities

NO.42 What is one of me benefits of using HPE Composer 2?

HPE Composer 2 has 128GB of memory and 4 AMD CPUs to improve performance of me management system

HPE Composer 2 modules are required to manage HPE virtual Connect SE 100GD F32 Modules for Synergy

The administrator can access an HPE Synergy Composer 2 appliance remotely to perform First Time Setup

A pair of HPE Composer 2 modules can manage 42 frames, compared to 21 frames managed by HPE Composer

NO.43 After HPE Superdome Flex deployment and nPar setup, you need to verify health status of HPE Superdome Flex components.
Put the steps on the left into the coned order on the right to perform this task.

[Q19-Q43] Attested HPE0-S60 Dumps PDF Resource [2023]

HP HPE0-S60 Exam Syllabus Topics: