[Jun-2023] Valid Way To Pass Cisco Exam Dumps with 200-301 Exam Study Guide [Q357-Q379] : Free Exams Dumps Materials : http://exams.dumpsmaterials.com

Q357. What are two benefits of using VTP in a switching environment? (Choose two.)

It allows switches to read frame tags.

It allows ports to be assigned to VLANs automatically.

It maintains VLAN consistency across a switched network.

It allows frames from multiple VLANs to use a single interface.

It allows VLAN information to be automatically propagated throughout the switching environment.

Q358. All physical cabling between the two switches is installed. Configure the network connectivity between the switches using the designated VLANs and interfaces.
1. Configure VLAN 100 named Compute and VLAN 200 named Telephony where required for each task.
2. Configure Ethernet0/1 on SW2 to use the existing VLAN named Available.
3. Configure the connection between the switches using access ports.
4. Configure Ethernet0/1 on SW1 using data and voice VLANs.
5. Configure Ethemet0/1 on SW2 so that the Cisco proprietary neighbor discovery protocol is turned off for the designated interface only.

Q359. A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link.

The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?

The OSPF area is not configured properly.

The priority on R1 should be set higher.

The cost on R1 should be set higher.

The hello and dead timers are not configured properly.

A backup designated router needs to be added to the network.

The OSPF process ID numbers must match.

Q360. Which two tasks must be performed to configure NTP to a trusted server in client mode on a single network device? (Choose two)

Enable NTP authentication.

Disable NTP broadcasts

Set the NTP server private key

Specify the IP address of the NTP server

Verify the time zone.

Q361. Which three statements about Syslog utilization are true? (Choose three.)

Utilizing Syslog improves network performance

The Syslog server automatically notifies the network administrator of network problems

A Syslog server provides the storage space necessary to store log files without using router disk space

There are more Syslog messages available within Cisco IOS than there are comparable SNMP trap messages.

Enabling Syslog on a router automatically enables NTP for accurate time stamping

A Syslog server helps in aggregation of logs and alerts.

Q362. Which type of address is the public IP address of a NAT device?

outside global

outsdwde local

inside global

insride local

outside public

inside public

Q363. What causes a port to be placed in the err-disabled state?

nothing plugged into the port

link flapping

shutdown command issued on the port

latency

Q364. R1 has learned route 192.168.12.0/24 via IS-IS. OSPF, RIP. and Internal EIGRP Under normal operating conditions, which routing protocol is installed in the routing table?

IS-IS

RIP

Internal EIGRP

OSPF

Q365. Which type of wireless encryption is used for WPA2 in preshared key mode?

TKIP with RC4

RC4

AES-128

AES-256

Q366. Drag drop the descriptions from the left onto the correct configuration-management technologies on the right.

The focus of Ansible is to be streamlined and fast, and to require no node agent installation.
Thus, Ansible performs all functions over SSH. Ansible is built on Python, in contrast to the Ruby foundation of Puppet and Chef.
TCP port 10002 is the command port. It may be configured in the Chef Push Jobs configuration file .
This port allows Chef Push Jobs clients to communicate with the Chef Push Jobs server.
Puppet is an open-source configuration management solution, which is built with Ruby and offers custom Domain Specific Language (DSL) and Embedded Ruby (ERB) templates to create custom Puppet language files, offering a declarative-paradigm programming approach.
A Puppet piece of code is called a manifest, and is a file with .pp extension.

Q367. How will Link Aggregation be implemented on a Cisco Wireless LAN Controller?

To pass client traffic two or more ports must be configured.

The EtherChannel must be configured in “mode active”

When enabled the WLC bandwidth drops to 500 Mbps

One functional physical port is needed to pass client traffic

Q368. Refer to the exhibit.

After configuring a new static route on the CPE. the engineer entered this series of commands to verify that the new configuration is operating normally When is the static default route installed into the routing table?

when 203 0 113.1 is no longer reachable as a next hop

when the default route learned over external BGP becomes invalid

when a route to 203.0 113 1 is learned via BGP

when the default route over external BGP changes its next hop

Q369. What is the function of northbound API?

It upgrades software and restores files.

It relies on global provisioning and configuration.

It supports distributed processing for configuration.

It provides a path between an SDN controller and network applications.

Q370. Drag and drop the threat-mitigation techniques from the left onto the types of threat or attack they mitigate on the right.

Q371. Refer to the exhibit. How should the configuration be updated to allow PC1 and PC2 access to the Internet?

Modify the configured number of the second access list.

Add either the ip nat {inside|outside} command under both interfaces.

Remove the overload keyword from the ip nat inside source command.

Change the ip nat inside source command to use interface GigabitEthernet0/0.

Q372. Which command you enter on a switch to display the ip address associated with connected devices?

Show cdp neighbors detail

Show cdp neighbor

Show cdp interface

Show cdp traffic

Q373. Refer to the exhibit.

To which device does Router1 send packets that are destined to host 10.10.13.165?

Router2

Router3

Router4

Router5

Q374. A network administrator is asked to configure VLANS 2, 3, and 4 for a new implementation. Some ports must be assigned to the new VLANS with unused ports remaining. Which action should be taken for the unused ports?

configure port in the native VLAN

configure ports in a black hole VLAN

configure in a nondefault native VLAN

configure ports as access ports

Q375. A network engineer is configuring a switch so that it is remotely reachable via SSH. The engineer has already configured the host name on the router. Which additional command must the engineer configure before entering the command to generate the RSA key?

crypto key generate rsa modulus 1024

ip ssh authentication-retries 2

password password

ip domain-name domain

Q376. While examining excessive traffic on the network, it is noted that all incoming packets on an interface appear to be allowed even though an IPv4 ACL is applied to the interface. Which two misconfigurations cause this behavior? (Choose two.)

The ACL is empty

A matching permit statement is too broadly defined

The packets fail to match any permit statement

A matching deny statement is too high in the access list

A matching permit statement is too high in the access list

Q377. Refer to the exhibit.

An engineer configured NAT translations and has verified that the configuration is correct.
Which IP address is the source IP?

10.4.4.4

10.4.4.5

172.23.103.10

172.23.104.4

Q378. Drag and drop the threat-mitigation techniques from the left onto the types of threat or attack they mitigate on the right.

Q379. Refer to exhibit

Which route type is configured to reach the internet?

host route

default route

floating static route

network route