Q357. What are two benefits of using VTP in a switching environment? (Choose two.)

Q358. All physical cabling between the two switches is installed. Configure the network connectivity between the switches using the designated VLANs and interfaces.
1. Configure VLAN 100 named Compute and VLAN 200 named Telephony where required for each task.
2. Configure Ethernet0/1 on SW2 to use the existing VLAN named Available.
3. Configure the connection between the switches using access ports.
4. Configure Ethernet0/1 on SW1 using data and voice VLANs.
5. Configure Ethemet0/1 on SW2 so that the Cisco proprietary neighbor discovery protocol is turned off for the designated interface only.

Q359. A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link.

The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?

Q360. Which two tasks must be performed to configure NTP to a trusted server in client mode on a single network device? (Choose two)

Q361. Which three statements about Syslog utilization are true? (Choose three.)

Q362. Which type of address is the public IP address of a NAT device?

Q363. What causes a port to be placed in the err-disabled state?

Q364. R1 has learned route 192.168.12.0/24 via IS-IS. OSPF, RIP. and Internal EIGRP Under normal operating conditions, which routing protocol is installed in the routing table?

Q365. Which type of wireless encryption is used for WPA2 in preshared key mode?

Q366. Drag drop the descriptions from the left onto the correct configuration-management technologies on the right.

The focus of Ansible is to be streamlined and fast, and to require no node agent installation.
Thus, Ansible performs all functions over SSH. Ansible is built on Python, in contrast to the Ruby foundation of Puppet and Chef.
TCP port 10002 is the command port. It may be configured in the Chef Push Jobs configuration file .
This port allows Chef Push Jobs clients to communicate with the Chef Push Jobs server.
Puppet is an open-source configuration management solution, which is built with Ruby and offers custom Domain Specific Language (DSL) and Embedded Ruby (ERB) templates to create custom Puppet language files, offering a declarative-paradigm programming approach.
A Puppet piece of code is called a manifest, and is a file with .pp extension.

Q367. How will Link Aggregation be implemented on a Cisco Wireless LAN Controller?

Q368. Refer to the exhibit.

After configuring a new static route on the CPE. the engineer entered this series of commands to verify that the new configuration is operating normally When is the static default route installed into the routing table?

Q369. What is the function of northbound API?

Q370. Drag and drop the threat-mitigation techniques from the left onto the types of threat or attack they mitigate on the right.

Q371. Refer to the exhibit. How should the configuration be updated to allow PC1 and PC2 access to the Internet?

Q372. Which command you enter on a switch to display the ip address associated with connected devices?

Q373. Refer to the exhibit.

To which device does Router1 send packets that are destined to host 10.10.13.165?

Q374. A network administrator is asked to configure VLANS 2, 3, and 4 for a new implementation. Some ports must be assigned to the new VLANS with unused ports remaining. Which action should be taken for the unused ports?

Q375. A network engineer is configuring a switch so that it is remotely reachable via SSH. The engineer has already configured the host name on the router. Which additional command must the engineer configure before entering the command to generate the RSA key?

Q376. While examining excessive traffic on the network, it is noted that all incoming packets on an interface appear to be allowed even though an IPv4 ACL is applied to the interface. Which two misconfigurations cause this behavior? (Choose two.)

Q377. Refer to the exhibit.

An engineer configured NAT translations and has verified that the configuration is correct.
Which IP address is the source IP?

Q378. Drag and drop the threat-mitigation techniques from the left onto the types of threat or attack they mitigate on the right.

Q379. Refer to exhibit

Which route type is configured to reach the internet?