100% Free JN0-349 Exam Dumps to Pass Exam Easily from DumpsMaterials [Q26-Q41]

NO.26 Exhibit.

Referring to the exhibit, which statement is correct?

The ge-0/0/15 interface is using the default port cost.

This switch has a bridge priority of 8k.

This switch is currently blocking all traffic.

The ge-0/0/9 interface is using the default interface priority value.

NO.27 You were provided a network diagram that told you to number your network from the
191.255.0.0/16 space. OSPF is enabled and adjacencies are up, but no routers are learning any
routes. What can explain this?

The default OSPF export policies advertise nothing, so you need to apply export policy

The default OSPF import policy rejects all OSPF routes, so you need to apply import policy

You need to modify the martian table with a 191.255.0.0/16 accept statement

You need to enable OSPF on the lo0 interface to provide a route to the RID of each router in the network

NO.28 You are running a Virtual Chassis with nonstop routing enabled. You want to confirm that the BGP routing table synchronization has completed on the backup Routing Engine.
Which command will show you this information?

show task replication

show bgp summary

show bgp neighbor

show bgp replication

NO.29 Referring to the exhibit, which two statements about BGP prefixes advertised by R1 to AS 65501
are true? (Choose two.)

R1 will modify the originator ID attribute in prefixes advertised to AS 65501

R1 will modify the AS path attribute in prefixes advertised to AS 65501

R1 will modify the next-hop attribute in prefixes advertised to AS 65501

R1 will modify the cluster list attribute in prefixes advertised to AS 65501

NO.30 You are deploying a new switch configuration at a small branch using EX3400 Series switches. You are concerned about loop prevention.
In this scenario, which configuration would you deploy?

RSTP

EVPN

MPLS

BPDU

NO.31 Click the Exhibit button.

Referring to the exhibit, which policy will export routes to IBGP peers?

static-3

static-4

static-1

static-2

NO.32 How many bytes of overhead are added to packet traversing a GRE tunnel?

NO.33 Which two OSPF header fields must match to form an adjacency over a broadcast connection?
(Choose two.)

Router priority

Options

Hello interval

neighbor

NO.34 You want to configure your Junos device so that routing information from certain prefixes on a
Neighboring router are ignored.
What should you configure on your device?

It interface

Firewall rule

Martian address

vt interface

NO.35 Exhibit.

Based on the traceoptions output shown in the exhibit, what is the problem with the adjacency?

authentication mismatch

area mismatch

connectivity

MTU mismatch

NO.36 Click the Exhibit button.

You are building a network and make some configuration changes. While trying to validate these changes, you receive the error shown in the exhibit.
How would you solve this problem?

You must create a new VLAN called all using the VLAN ID of 30.

You must configure the ge-0/0/5.0 interface with family inet instead of family ethernet-switching.

You must configure the port mode as trunk on the ge-0/0/5.0 interface.

You must create two sub-interfaces on ge-0/0/5 with the appropriate VLAN member assigned to each.

NO.37 You want to advertise only a default route into a new area, which will be called area 7.
In this scenario, which configuration statement would solve this problem?

user@host# set protocols ospf area 0.0.0.7 nssa default-lsa default-metric10

user@host# set protocols ospf area 0.0.0.7 stub no-summaries

user@host# set protocols ospf area 0.0.0.7 stub default-metric 10

user@host# set protocols ospf area 0.0.0.7 stub

NO.38 Which statement is correct about 1S IS link state PDUs?

They are used to maintain link slid.: database synchronization

They are used to establish adjacencies

They are used to build the link state database.

They are used to determine whether the neighbors are Level 1 or Level 2

NO.39 Referring to the exhibit, Router-1 is attempting to form an EBGP session with Router-2. However,
BGP routes are never exchanged between Router-1 and Router-2.

What is causing the problem?