2024 Updated HP HPE6-A72 Dumps PDF - Want To Pass HPE6-A72 Fast [Q47-Q68] : Free Exams Dumps Materials : http://exams.dumpsmaterials.com

NO.47 Refer to the exhibit.

The above output is the result of issuing the command show system resource-utilization.
What command should be used to enable terminal output line by line or page by page?

The command page

The command terminal length 30

The command more

The command less

NO.48 Which statement is true regarding modern switching requirements?

Most older legacy switches had high port bandwidth utilization and were future proof designed to meet today’s power-over-Ethernet needs.

Requirements for PoE are normally addressed using AC to DC power adapters. Concerns for port security for IoT devices are usually addressed using default wired encryption that all 802.3 Ethernet switches provide.

While APs are common, most clients are still docked and only require traditional wired connections with only the occasional dedicated PoE switch to provide power for the low number of devices needed.

Clients tend to prefer wireless connections, raising the need for PoE port access. There is also a growing amount of IoT devices that require security and port authentication options.

NO.49 Match each description to the correct term.

NO.50 What are two primary concerns regarding layer two loops in a redundant topology? (Choose two.)

routing loops

costs associated with upgrading from copper to fiber

multiple frame copies leading to instability of the MAC address table

security issues with a redundant loop indicating to hackers that a back-door exists

broadcast storms

NO.51 SW1(config)# interface 1/1/1-1/1/2
SW1(config-if-<1/1/1-1/1/2)# vlan access 2
SW1(config-if-<1/1/1-1/1/2)# exit
SW1(config)# interface 1/1/11-1/1/17
SW1(config-if-<1/1/11-1/1/17)# vlan access 17
SW1(config-if-<1/1/11-1/1/17)# exit
After completing the above commands, what is the expected output of show vlan with no other vlan commanded having been added?

Option A

Option B

Option C

Option D

NO.52 What command will save your configuration on an Aruba AOS-CX switch so that your changes automatically load on next reboot?

copy running-config checkpoint startup-config

copy startup-config running-config

copy running-config initial-checkpoint

copy running-config default

NO.53 What are two methods for remotely managing an Aruba AOS-CX switch? (Choose two.)

SNMPv2c

HTTPS

USB-C console

Telnet

SSH

NO.54 ServiceOS login: admin
SVOS> password
Enter password: ********
Confirm password: ********
The login password to access an Aruba AOS-CX was lost. After connecting to the switch console port, a reboot is performed and the Service OS console is accessed as shown above.
What is the default password that is required for the admin account while under the Service OS console?

No password is set for this account.

“password”

“forgetme!”

The same login password that has lost originally.

NO.55 Match each network protocol to the correct server listening port. Not all answers will be used.

NO.56 Match the switching term to the correct definition.

NO.57 Refer to the exhibit

What is true regarding VLAN 50 according to the diagram above?

VLAN 50 is part of a switched virtual interface (SVI) that was never routed causing it to be down.

Since VLAN 50 has not been assigned to any enabled physical port, the status is down.

VLAN 50 is assigned only to Trunk ports which is why no ports are listed under interfaces.

VLAN 50 was never added to the vlan-database and therefore is in a down state.

NO.58 Refer to the exhibit.

What commands will successfully enable the SVI for vlan 100 on interface 1/1/1 to produce the results displayed in the command show ip interface brief in the exhibit below?

Access-1(config)# interface 1/1/1
Access-1(config-if)# routing
Access-1(config-if)# interface vlan 100
Access-1(config-if-vlan)# ip address 10.1.1.1/24

Access-1(config)# interface 1/1/1
Access-1(config-if)# vlan trunk permit vlan 100
Access-1(config-if)# interface vlan 100
Access-1(config-if-vlan)# ip address static 10.1.1.1/24

Access-1(config)# interface vlan 100
Access-1(config-if-vlan)# ip address 10.1.1.1/24

Access-1(config-if)# vlan 100
Access-1(config-vlan)# ip address 10.1.1.1/24

NO.59 Refer to the exhibit.

Which command produces the above output?

show interface port 1/1/10 trunk

show vlan port 1/1/10

show trunk port 1/1/10 extended

show interface port 1/1/10 switchport

NO.60 Which two types of routes can be found in the IP routing table of an Aruba AOS-CX switch? (Choose two.)

Local

EIGRP

BGP

ISIS

RIPng

NO.61 Refer to the exhibit.

All four switches in the diagram have been configured with the region name “Aruba1”.
What two other MSTP configurations must match for switches within the same MST region? (Choose two.)

MST region type

MST Bridge ID

MST version number

MST revision number

MST VLAN to instance mapping

NO.62 Which port or ports should be allowed through a firewall so that an AOS-CX switch can act as an SNMP Agent?

UDP 1812 and UDP 1813

UDP 161

TCP 443

UDP 162

NO.63 Which two statements are true regarding Checkpoints on Aruba switches? (Choose two.)

Rolling back to a prior checkpoint triggers a reboot of the switch.

Stacking switches using VSF or VSX will disable the Checkpoint feature.

A checkpoint is a snapshot of the running-configuration and relevant metadata at the time the checkpoint was created.

System-generated checkpoints are created after a configuration change and 5 minutes of inactivity.

Checkpoints are available on AOS 5400R switches, as well as on all AOS-CX switches.

NO.64 What are the benefits of a 3-Tier design over a 2-Tier? (Choose two.)

Offloading processing from the Core without routing at the Access layer.

Can use lower speed links between Core to Aggregation and Aggregation to Access given the use of an Aggregation layer.

Lowering the cost of a deployment due to needing less switches overall.

Better scalability in a campus with a large number of buildings.

Gaining the flexibility to connect the Data-Center to any Access layer switch.

NO.65 The following command is issued:
Switch# checkpoint rollback start
What is the result?

The command will fail because rollback commands must be issued from global-config mode.

The switch will revert the running-configuration to the checkpoint called ‘start1 without a reboot.

The command will fail because it is incomplete.

The switch will use the checkpoint ‘rollback1 as the starting configuration on next reboot.

NO.66 Refer to the exhibit.

Using the static IP address configured above, what is the converted binary value of the third octet assigned to the local interface?

11010101

10110001

01001011

11111000

NO.67 Match each description to the correct term.

NO.68 What are the commands to disable SSH and HTTPS services from the default VRF?

Core-1(config)# no ssh server
Core-1(config)# no https-server

Core-1# no ssh server vrf default
Core-1# no https-server vrf default

Core-1(config)# no ssh server enable
Core-1(config)# no https-server enable

Core-1(config)# no ssh server vrf default
Core-1(config)# no https-server vrf default

2024 Updated HP HPE6-A72 Dumps PDF - Want To Pass HPE6-A72 Fast [Q47-Q68]

Understanding functional and technical aspects of Aruba Certified Switching Associate (HP HPE6-A72) Professional Exam Design for Stacking