[Mar 20, 2025] Get New N10-009 Certification Practice Test Questions Exam Dumps [Q18-Q40]

Q18. Which of the following most likely requires the use of subinterfaces?

Q19. A network administrator is configuring access points for installation in a dense environment where coverage is often overlapping. Which of the following channel widths should the administrator choose to help minimize interference in the 2.4GHz spectrum?

Q20. A network engineer is completing a wireless installation in a new building. A requirement is that all clients be able to automatically connect to the fastest supported network. Which of the following best supports this requirement?

Q21. A network administrator for a small office is adding a passive IDS to its network switch for the purpose of inspecting network traffic. Which of the following should the administrator use?

Q22. Which of the following fiber connector types is the most likely to be used on a network interface card?

Q23. A company is implementing a wireless solution in a high-density environment. Which of the following 802.11 standards is used when a company is concerned about device saturation and converage?

Q24. A network administrator is notified that a user cannot access resources on the network. The network administrator checks the physical connections to the workstation labeled User 3 and sees the Ethernet is properly connected. However, the network interface’s indicator lights are not blinking on either the computer or the switch. Which of the following Is the most likely cause?

Q25. Early in the morning, an administrator installs a new DHCP server. In the afternoon, some users report they are experiencing network outages. Which of the following is the most likely issue?

Q26. A network technician needs to resolve some issues with a customer’s SOHO network. The customer reports that some of the PCs are not connecting to the network, while others appear to be working as intended.
지침
Troubleshoot all the network components.
Review the cable test results first, then diagnose by clicking on the appropriate PC, server, and Layer 2 switch.
Identify any components with a problem and recommend a solution to correct each problem.
If at any time you would like to bring back
the initial state of the simulation, please
click the Reset All button.

Q27. A network administrator is notified that a user cannot access resources on the network. The network administrator checks the physical connections to the workstation labeled User 3 and sees the Ethernet is properly connected. However, the network interface’s indicator lights are not blinking on either the computer or the switch. Which of the following Is the most likely cause?

Q28. A network administrator is connecting two Layer 2 switches in a network. These switches must transfer data in multiple networks. Which of the following would fulfill this requirement?

Q29. Which of the following steps of the troubleshooting methodology should a technician take to confirm a theory?

Q30. A network administrator is connecting two Layer 2 switches in a network. These switches must transfer data in multiple networks. Which of the following would fulfill this requirement?

Q31. Which of the following protocols provides remote access utilizing port 22?

Q32. Which of the following appliances provides users with an extended footprint that allows connections from multiple devices within a designated WLAN?

Q33. After running a Cat 8 cable using passthrough plugs, an electrician notices that connected cables are experiencing a lot of cross talk. Which of the following troubleshooting steps should the electrician take first?

Q34. A support agent receives a report that a remote user’s wired devices are constantly disconnecting and have slow speeds. Upon inspection, the support agent sees that the user’s coaxial modern has a signal power of -97dB.

Q35. Which of the following ports is used for secure email?

Q36. A network technician replaced an access layer switch and needs to reconfigure it to allow the connected devices to connect to the correct networks.
지침
Click on the appropriate port(s) on Switch 1 and Switch 3 to verify or reconfigure the correct settings:
Ensure each device accesses only its
correctly associated network.
Disable all unused switchports.
. Require fault-tolerant connections
between the switches.
. Only make necessary changes to
complete the above requirements.

Q37. Which of the following most likely requires the use of subinterfaces?

Q38. Users are unable to access files on their department share located on file server 2.
The network administrator has been tasked with validating routing between networks hosting workstation A and file server 2.
지침
Click on each router to review output, identify any issues, and configure the appropriate solution.
언제든지 시뮬레이션의 초기 상태로 되돌리려면 모두 초기화 버튼을 클릭하세요.

Q39. 시뮬레이션
You have been tasked with setting up a wireless network in an office. The network will consist of 3 Access Points and a single switch. The network must meet the following parameters:
The SSIDs need to be configured as CorpNet with a key of S3cr3t!
The wireless signals should not interfere with each other
The subnet the Access Points and switch are on should only support 30 devices maximum The Access Points should be configured to only support TKIP clients at a maximum speed INSTRUCTONS Click on the wireless devices and review their information and adjust the settings of the access points to meet the given requirements.
언제든지 시뮬레이션의 초기 상태로 되돌리려면 모두 초기화 버튼을 클릭하세요.

Q40. Users are unable to access files on their department share located on file server 2.
The network administrator has been tasked with validating routing between networks hosting workstation A and file server 2.
지침
Click on each router to review output, identify any issues, and configure the appropriate solution.
언제든지 시뮬레이션의 초기 상태로 되돌리려면 모두 초기화 버튼을 클릭하세요.