100% Free Fortinet Network Security Expert NSE8_812 Dumps PDF Demo Cert Guide Cover [Q20-Q42]

May 5, 2024 examdumps 0 Comment

Tags: NSE8_812 latest braindumps pdf, NSE8_812 latest exam simulator, NSE8_812 latest test questions pdf, NSE8_812 reliable exam dumps.zip, NSE8_812 valid braindumps ebook, NSE8_812 valid dumps ebook, NSE8_812 valid exam pass4sure

4/5 - (1 vote)

100% Free Fortinet Network Security Expert NSE8_812 Dumps PDF Demo Cert Guide Cover

PDF Exam Material 2024 Realistic NSE8_812 Dumps Questions

Fortinet NSE8_812 certification is highly respected in the network security industry and is recognized worldwide. It demonstrates that the holder has a deep understanding of network security and can design and implement advanced security solutions using Fortinet products. Fortinet NSE 8 – Written Exam (NSE8_812) certification is particularly valuable for network security professionals who work with large organizations or government agencies that require the highest level of security protection.

NO.20 Refer to the exhibits.

An administrator has configured a FortiGate and Forti Authenticator for two-factor authentication with FortiToken push notifications for their SSL VPN login. Upon initial review of the setup, the administrator has discovered that the customers can manually type in their two-factor code and authenticate but push notifications do not work Based on the information given in the exhibits, what must be done to fix this?

On FG-1 port1, the ftm access protocol must be enabled.

FAC-1 must have an internet routable IP address for push notifications.

On FG-1 CLI, the ftm-push server setting must point to 100.64.141.

On FAC-1, the FortiToken public IP setting must point to 100.64.1 41

NO.21 Refer to the exhibit.

The exhibit shows two error messages from a FortiGate root Security Fabric device when you try to configure a new connection to a FortiClient EMS Server.
Referring to the exhibit, which two actions will fix these errors? (Choose two.)

Verify that the CRL is accessible from the root FortiGate

Export and import the FortiClient EMS server certificate to the root FortiGate.

Install a new known CA on the Win2K16-EMS server.

Authorize the root FortiGate on the FortiClient EMS

NO.22 You are troubleshooting a FortiMail Cloud service integrated with Office 365 where outgoing emails are not reaching the recipients’ mail What are two possible reasons for this problem? (Choose two.)

The FortiMail access control rule to relay from Office 365 servers FQDN is missing.

The FortiMail DKIM key was not set using the Auto Generation option.

The FortiMail access control rules to relay from Office 365 servers public IPs are missing.

A Mail Flow connector from the Exchange Admin Center has not been set properly to the FortiMail Cloud FQDN.

NO.23 You must configure an environment with dual-homed servers connected to a pair of FortiSwitch units using an MCLAG.
Multicast traffic is expected in this environment, and you should ensure unnecessary traffic is pruned from links that do not have a multicast listener.
In which two ways must you configure the igmps-f lood-traffic and igmps-flood-report settings? (Choose two.)

disable on ICL trunks

enable on ICL trunks

disable on the ISL and FortiLink trunks

enable on the ISL and FortiLink trunks

NO.24 Refer to the exhibits.
Exhibit A

Exhibit B

Exhibit C

A customer is trying to set up a VPN with a FortiGate, but they do not have a backup of the configuration. Output during a troubleshooting session is shown in the exhibits A and B and a baseline VPN configuration is shown in Exhibit C Referring to the exhibits, which configuration will restore VPN connectivity?

NO.25 Refer to the exhibits.

A customer wants to deploy 12 FortiAP 431F devices on high density conference center, but they do not currently have any PoE switches to connect them to. They want to be able to run them at full power while having network redundancy From the FortiSwitch models and sample retail prices shown in the exhibit, which build of materials would have the lowest cost, while fulfilling the customer’s requirements?

1x FortiSwitch 248EFPOE

2x FortiSwitch 224E-POE

2x FortiSwitch 248E-FPOE

2x FortiSwitch 124E-FPOE

The customer wants to deploy 12 FortiAP 431F devices on a high density conference center, but they do not have any PoE switches to connect them to. They want to be able to run them at full power while having network redundancy. PoE switches are switches that can provide both data and power to connected devices over Ethernet cables, eliminating the need for separate power adapters or outlets. PoE switches are useful for deploying devices such as wireless access points, IP cameras, and VoIP phones in locations where power outlets are scarce or inconvenient. The FortiAP 431F is a wireless access point that supports PoE+ (IEEE 802.3at) standard, which can deliver up to 30W of power per port. The FortiAP 431F has a maximum power consumption of 25W when running at full power. Therefore, to run 12 FortiAP 431F devices at full power, the customer needs PoE switches that can provide at least 300W of total PoE power budget (25W x 12). The customer also needs network redundancy, which means that they need at least two PoE switches to connect the FortiAP devices in case one switch fails or loses power. From the FortiSwitch models and sample retail prices shown in the exhibit, the build of materials that has the lowest cost while fulfilling the customer’s requirements is 2x FortiSwitch 248E-FPOE. The FortiSwitch 248E-FPOE is a PoE switch that has 48 GE ports with PoE+ capability and a total PoE power budget of 370W. It also has 4x 10 GE SFP+ uplink ports for high-speed connectivity. The sample retail price of the FortiSwitch 248E-FPOE is $1,995, which means that two units will cost $3,990. This is the lowest cost among the other options that can meet the customer’s requirements. Option A is incorrect because the FortiSwitch 248EFPOE is a non-PoE switch that has no PoE capability or power budget. It cannot provide power to the FortiAP devices over Ethernet cables. Option B is incorrect because the FortiSwitch 224E-POE is a PoE switch that has only 24 GE ports with PoE+ capability and a total PoE power budget of 185W. It cannot provide enough ports or power to run 12 FortiAP devices at full power. Option D is incorrect because the FortiSwitch 124E-FPOE is a PoE switch that has only 24 GE ports with PoE+ capability and a total PoE power budget of 185W. It cannot provide enough ports or power to run 12 FortiAP devices at full power. References: https://www.fortinet.com/content/dam/fortinet/assets/data-sheets/FortiSwitch_Secure_Access_Series.pdf https://www.fortinet.com/content/dam/fortinet/assets/data-sheets/FortiAP_400_Series.pdf

NO.26 Review the following FortiGate-6000 configuration excerpt:

Based on the configuration, which statement is correct regarding SNAT source port partitioning behavior?

It dynamically distributes SNAT source ports to operating FPCs or FPMs.

It is the default SNAT configuration and preserves active sessions when an FPC or FPM goes down.

It statically distributes SNAT source ports to operating FPCs or FPMs

It equally distributes SNAT source ports across chassis slots.

NO.27 Refer to the exhibit.

You are operating an internal network with multiple OSPF routers on the same LAN segment. FGT_3 needs to be added to the OSPF network and has the configuration shown in the exhibit. FGT_3 is not establishing any OSPF connection.
What needs to be changed to the configuration to make sure FGT_3 will establish OSPF neighbors without affecting the DR/BDR election?

NO.28 You are responsible for recommending an adapter type for NICs on a FortiGate VM that will run on an ESXi Hypervisor. Your recommendation must consider performance as the main concern, cost is not a factor. Which adapter type for the NICs will you recommend?

Native ESXi Networking with E1000

Virtual Function (VF) PCI Passthrough

Native ESXi Networking with VMXNET3

Physical Function (PF) PCI Passthrough

NO.29 Refer to the exhibits.

The exhibits show a FortiMail network topology, Inbound configuration settings, and a Dictionary Profile.
You are required to integrate a third-party’s host service (srv.thirdparty.com) into the e-mail processing path.
All inbound e-mails must be processed by FortiMail antispam and antivirus with FortiSandbox integration. If the email is clean, FortiMail must forward it to the third-party service, which will send the email back to FortiMail for final delivery, FortiMail must not scan the e-mail again.
Which three configuration tasks must be performed to meet these requirements? (Choose three.)

Change the scan order in FML-GW to antispam-sandbox-content.

Apply the Catch-Ail profile to the CFInbound profile and configure a content action profile to deliver to the srv. thirdparty. com FQDN

Create an access receive rule with a Sender value of srv. thirdparcy.com, Recipient value of *@acme.com, and action value of Safe

Apply the Catch-AII profile to the ASinbound profile and configure an access delivery rule to deliver to the 100.64.0.72 host.

Create an IP policy with a Source value of 100. 64 .0.72/32, enable precedence, and place the policy at the top of the list.

NO.30 Refer to the exhibits.

A customer has deployed a FortiGate with iBGP and eBGP routing enabled. HQ is receiving routes over eBGP from ISP 2; however, only certain routes are showing up in the routing table-Assume that BGP is working perfectly and that the only possible modifications to the routing table are solely due to the prefix list that is applied on HQ.
Given the exhibits, which two routes will be active in the routing table on the HQ firewall? (Choose two.)

172.16.204.128/25

172.16.201.96/29

172,620,64,27

172.16.204.64/27

NO.31 A customer wants to use the FortiAuthenticator REST API to retrieve an SSO group called SalesGroup. The following API call is being made with the ‘curl’ utility:

Which two statements correctly describe the expected behavior of the FortiAuthenticator REST API? (Choose two.)

Only users with the “Full permission” role can access the REST API

This API call will fail because it requires that API version 2

If the REST API web service access key is lost, it cannot be retrieved and must be changed.

The syntax is incorrect because the API calls needs the get method.

NO.32 Refer to the exhibits.

A customer wants to deploy 12 FortiAP 431F devices on high density conference center, but they do not currently have any PoE switches to connect them to. They want to be able to run them at full power while having network redundancy From the FortiSwitch models and sample retail prices shown in the exhibit, which build of materials would have the lowest cost, while fulfilling the customer’s requirements?

1x FortiSwitch 248EFPOE

2x FortiSwitch 224E-POE

2x FortiSwitch 248E-FPOE

2x FortiSwitch 124E-FPOE

The customer wants to deploy 12 FortiAP 431F devices on a high density conference center, but they do not have any PoE switches to connect them to. They want to be able to run them at full power while having network redundancy. PoE switches are switches that can provide both data and power to connected devices over Ethernet cables, eliminating the need for separate power adapters or outlets. PoE switches are useful for deploying devices such as wireless access points, IP cameras, and VoIP phones in locations where power outlets are scarce or inconvenient. The FortiAP 431F is a wireless access point that supports PoE+ (IEEE 802.3at) standard, which can deliver up to 30W of power per port. The FortiAP 431F has a maximum power consumption of 25W when running at full power. Therefore, to run 12 FortiAP 431F devices at full power, the customer needs PoE switches that can provide at least 300W of total PoE power budget (25W x 12). The customer also needs network redundancy, which means that they need at least two PoE switches to connect the FortiAP devices in case one switch fails or loses power. From the FortiSwitch models and sample retail prices shown in the exhibit, the build of materials that has the lowest cost while fulfilling the customer’s requirements is 2x FortiSwitch 248E-FPOE. The FortiSwitch 248E-FPOE is a PoE switch that has 48 GE ports with PoE+ capability and a total PoE power budget of 370W. It also has 4x 10 GE SFP+ uplink ports for high-speed connectivity. The sample retail price of the FortiSwitch 248E-FPOE is $1,995, which means that two units will cost $3,990. This is the lowest cost among the other options that can meet the customer’s requirements. Option A is incorrect because the FortiSwitch 248EFPOE is a non-PoE switch that has no PoE capability or power budget. It cannot provide power to the FortiAP devices over Ethernet cables. Option B is incorrect because the FortiSwitch 224E-POE is a PoE switch that has only 24 GE ports with PoE+ capability and a total PoE power budget of 185W. It cannot provide enough ports or power to run 12 FortiAP devices at full power. Option D is incorrect because the FortiSwitch 124E-FPOE is a PoE switch that has only 24 GE ports with PoE+ capability and a total PoE power budget of 185W. It cannot provide enough ports or power to run 12 FortiAP devices at full power. Reference: https://www.fortinet.com/content/dam/fortinet/assets/data-sheets/FortiSwitch_Secure_Access_Series.pdf https://www.fortinet.com/content/dam/fortinet/assets/data-sheets/FortiAP_400_Series.pdf

NO.33 Refer to the CLI output:

Given the information shown in the output, which two statements are correct? (Choose two.)

Geographical IP policies are enabled and evaluated after local techniques.

Attackers can be blocked before they target the servers behind the FortiWeb.

The IP Reputation feature has been manually updated

An IP address that was previously used by an attacker will always be blocked

Reputation from blacklisted IP addresses from DHCP or PPPoE pools can be restored

NO.34 A retail customer with a FortiADC HA cluster load balancing five webservers in L7 Full NAT mode is receiving reports of users not able to access their website during a sale event. But for clients that were able to connect, the website works fine.
CPU usage on the FortiADC and the web servers is low, application and database servers are still able to handle more traffic, and the bandwidth utilization is under 30%.
Which two options can resolve this situation? (Choose two.)

Change the persistence rule to LB_PERSIS_SSL_SESSJD.

Add more web servers to the real server poof

Disable SSL between the FortiADC and the web servers

Add a connection-pool to the FortiADC virtual server

The FortiADC HA cluster is a load balancing solution that distributes traffic among multiple web servers in L7 Full NAT mode. L7 Full NAT mode means that FortiADC terminates both client and server SSL connections and performs full NAT for both source and destination IP addresses and ports. One possible reason for users not being able to access the website during a sale event is that the persistence rule is not configured properly. Persistence rule is a feature that ensures that subsequent requests from the same client are sent to the same web server, which is important for maintaining session continuity and avoiding errors or data loss. The default persistence rule for L7 Full NAT mode is LB_PERSIS_SRC_IP, which uses the source IP address of the client as the persistence key. However, this rule may not work well if there are many clients behind a proxy or NAT device that share the same source IP address, or if there are clients that change their source IP address frequently due to roaming or switching networks. Therefore, to resolve this situation, one option is to change the persistence rule to LB_PERSIS_SSL_SESSJD, which uses the SSL session ID of the client as the persistence key. This rule can provide more accurate and reliable persistence for SSL connections than LB_PERSIS_SRC_IP. Another possible reason for users not being able to access the website during a sale event is that there are too many TCP connections being established and terminated between FortiADC and the web servers, which consumes CPU resources and causes performance degradation. Therefore, to resolve this situation, another option is to add a connection-pool to the FortiADC virtual server. Connection-pool is a feature that allows FortiADC to reuse existing TCP connections between FortiADC and the web servers, instead of creating new ones for each request. This can reduce CPU overhead, improve response time, and increase throughput. Reference: https://docs.fortinet.com/document/fortiadc/6.4.0/administration-guide/19662/load-balancing-methods-and-persistence https://docs.fortinet.com/document/fortiadc/6.4.0/administration-guide/19662/connection-pool

NO.35 Refer to the exhibits.

The exhibits show a FortiGate network topology and the output of the status of high availability on the FortiGate.
Given this information, which statement is correct?

The ethertype values of the HA packets are 0x8890, 0x8891, and 0x8892

The cluster mode can support a maximum of four (4) FortiGate VMs

The cluster members are on the same network and the IP addresses were statically assigned.

FGVMEVLQOG33WM3D and FGVMEVGCJNHFYI4A share a virtual MAC address.

NO.36 Refer to the exhibit showing FortiGate configurations

FortiManager VM high availability (HA) is not functioning as expected after being added to an existing deployment.
The administrator finds that VRRP HA mode is selected, but primary and secondary roles are greyed out in the GUI The managed devices never show online when FMG-B becomes primary, but they will show online whenever the FMG-A becomes primary.
What change will correct HA functionality in this scenario?

Change the FortiManager IP address on the managed FortiGate to 10.3.106.65.

Make the monitored IP to match on both FortiManager devices.

Unset the primary and secondary roles in the FortiManager CLI configuration so VRRP will decide who is primary.

Change the priority of FMG-A to be numerically lower for higher preference

NO.37 Which two methods are supported for importing user defined Lookup Table Data into the FortiSIEM? (Choose two.)

API

FTP

SCP

Report

NO.38 Refer to the exhibit.

To facilitate a large-scale deployment of SD-WAN/ADVPN with FortiGate devices, you are tasked with configuring the FortiGate devices to support injecting of IKE routes on the ADVPN shortcut tunnels.
Which three commands must be added or changed to the FortiGate spoke config vpn ipsec phasei-interface options referenced in the exhibit for the VPN interface to enable this capability? (Choose three.)

set net-device disable

set mode-cfg enable

set ike-version 1

set add-route enable

set mode-cfg-allow-client-selector enable

NO.39 Which two methods are supported for importing user defined Lookup Table Data into the FortiSIEM? (Choose two.)

Report

FTP

API

SCP

NO.40 Refer to the exhibit.

To facilitate a large-scale deployment of SD-WAN/ADVPN with FortiGate devices, you are tasked with configuring the FortiGate devices to support injecting of IKE routes on the ADVPN shortcut tunnels.
Which three commands must be added or changed to the FortiGate spoke config vpn ipsec phasei-interface options referenced in the exhibit for the VPN interface to enable this capability? (Choose three.)

set net-device disable

set mode-cfg enable

set ike-version 1

set add-route enable

set mode-cfg-allow-client-selector enable

NO.41 Refer to the exhibit.

FortiManager is configured with the Jinja Script under CLI Templates shown in the exhibit.
Which two statements correctly describe the expected behavior when running this template? (Choose two.)

The Jinja template will automatically map the interface with “WAN” role on the managed FortiGate.

The template will work if you change the variable format to $(WAN).

The template will work if you change the variable format to {{ WAN }}.

The administrator must first manually map the interface for each device with a meta field.

The template will fail because this configuration can only be applied with a CLI or TCL script.

NO.42 Refer to the exhibit, which shows a Branch1 configuration and routing table.

In the SD-WAN implicit rule, you do not want the traffic load balance for the overlay interface when all members are available.
In this scenario, which configuration change will meet this requirement?

Change the load-balance-mode to source-ip-based.

Create a new static route with the internet sdwan-zone only

Configure the cost in each overlay member to 10.

Configure the priority in each overlay member to 10.

Fortinet NSE8_812 certification is recognized globally as a mark of proficiency in advanced network security. Fortinet NSE 8 – Written Exam (NSE8_812) certification is particularly useful for network security professionals who are responsible for designing, implementing, and managing complex security infrastructures for large organizations. With the NSE 8 certification, professionals can demonstrate their expertise in advanced network security and gain a competitive advantage in their careers.

Updated Fortinet NSE8_812 Dumps – PDF & Online Engine: https://www.dumpsmaterials.com/NSE8_812-real-torrent.html