All Obstacles During JN0-637 Exam Preparation with JN0-637 Real Test Questions [Q55-Q76]

NEW QUESTION 55
Which two security intelligence feed types are supported?

infected host feed

Command and Control feed

custom feeds

malicious URL feed

NEW QUESTION 56
Exhibit

Referring to the exhibit, which two statements are true about the CAK status for the CAK named
“FFFP”? (Choose two.)

CAK is not used for encryption and decryption of the MACsec session.

SAK is successfully generated using this key.

CAK is used for encryption and decryption of the MACsec session.

SAK is not generated using this key.

NEW QUESTION 57
Exhibit

You are validating bidirectional traffic flows through your IPsec tunnel. The 4546 session represents traffic being sourced from the remote end of the IPsec tunnel. The 4547 session represents traffic that is sourced from the local network destined to the remote network.
Which statement is correct regarding the output shown in the exhibit?

The remote gateway address for the IPsec tunnel is 10.20.20.2

The session information indicates that the IPsec tunnel has not been established

The local gateway address for the IPsec tunnel is 10.20.20.2

NAT is being used to change the source address of outgoing packets

NEW QUESTION 58
You are asked to control access to network resources based on the identity of an authenticated device.
Which three steps will accomplish this goal on the SRX Series firewalls? (Choose three)

Configure an end-user-profile that characterizes a device or set of devices

Reference the end-user-profile in the security zone

Reference the end-user-profile in the security policy.

Apply the end-user-profile at the interface connecting the devices

Configure the authentication source to be used to authenticate the device

To control access to network resources based on the identity of an authenticated device on the SRX Series firewalls, you need to perform the following steps:
A) Configure an end-user-profile that characterizes a device or set of devices. An end-user-profile is a device identity profile that contains a collection of attributes that are characteristics of a specific group of devices, or of a specific device, depending on the attributes configured in the profile. The end-user- profile must contain a domain name and at least one value in each attribute. The attributes include device-identity, device-category, device-vendor, device-type, device-os, and device-os-version1. You can configure an end-user-profile by using the Junos Space Security Director or the CLI2.
C) Reference the end-user-profile in the security policy. A security policy is a rule that defines the action to be taken for the traffic that matches the specified criteria, such as source and destination addresses, zones, protocols, ports, and applications. You can reference the end-user-profile in the source-end-user- profile field of the security policy to identify the traffic source based on the device from which the traffic issued. The SRX Series device matches the IP address of the device to the end-user-profile and applies the security policy accordingly3. You can reference the end-user-profile in the security policy by using the Junos Space Security Director or the CLI4.
E) Configure the authentication source to be used to authenticate the device. An authentication source is a system that provides the device identity information to the SRX Series device. The authentication source can be Microsoft Windows Active Directory or a third-party network access control (NAC) system.
You need to configure the authentication source to be used to authenticate the device and to send the device identity information to the SRX Series device. The SRX Series device stores the device identity information in the device identity authentication table5. You can configure the authentication source by using the Junos Space Security Director or the CLI6.
The other options are incorrect because:
B) Referencing the end-user-profile in the security zone is not a valid step to control access to network resources based on the identity of an authenticated device. A security zone is a logical grouping of interfaces that have similar security requirements. You can reference the user role in the security zone to identify the user who is accessing the network resources, but not the end-user-profile7.
D) Applying the end-user-profile at the interface connecting the devices is also not a valid step to control access to network resources based on the identity of an authenticated device. You cannot apply the end- user-profile at the interface level, but only at the security policy level. The end-user-profile is not a firewall filter or a security policy, but a device identity profile that is referenced in the security policy1.
Reference: End User Profile Overview Creating an End User Profile source-end-user-profile Creating Firewall Policy Rules Understanding the Device Identity Authentication Table and Its Entries Configuring the Authentication Source for Device Identity user-role

NEW QUESTION 59
You are not able to activate the SSH honeypot on the all-in-one Juniper ATP appliance.
What would be a cause of this problem?

The collector must have a minimum of two interfaces.

The collector must have a minimum of three interfaces.

The collector must have a minimum of five interfaces.

The collector must have a minimum of four interfaces.

NEW QUESTION 60
Your company wants to use the Juniper Seclntel feeds to block access to known command and control servers, but they do not want to use Security Director to manage the feeds.
Which two Juniper devices work in this situation? (Choose two)

EX Series devices

MX Series devices

SRX Series devices

QFX Series devices

NEW QUESTION 61
Exhibit:

You are troubleshooting a firewall filter shown in the exhibit that is intended to log all traffic and block only inbound telnet traffic on interface ge-0/0/3.
How should you modify the configuration to fulfill the requirements?

Modify the log-all term to add the next term action

Delete the log-all term

Add a term before the log-all term that blocks Telnet

Apply a firewall filter to the loopback interface that blocks Telnet traffic

NEW QUESTION 62
You are required to deploy a security policy on an SRX Series device that blocks all known Tor network IP addresses.
Which two steps will fulfill this requirement? (Choose two.)

Enroll the devices with Juniper ATP Appliance.

Enroll the devices with Juniper ATP Cloud.

Enable a third-party Tor feed.

Create a custom feed containing all current known MAC addresses.

NEW QUESTION 63
Exhibit:

The security trace options configuration shown in the exhibit is committed to your SRX series firewall.
Which two statements are correct in this Scenario? (Choose Two)

The file debugger will be readable by all users.

Once the trace has generated 10 log files, older logs will be overwritten.

Once the trace has generated 10 log files, the trace process will halt.

The file debugger will be readable only by the user who committed this configuration

NEW QUESTION 64
Exhibit

Referring to the exhibit, which three protocols will be allowed on the ge-0/0/5.0 interface? (Choose three.)

IBGP

OSPF

IPsec

DHCP

NTP

NEW QUESTION 65
You have the NAT rule, shown in the exhibit, applied to allow communication across an IPsec tunnel between your two sites with identical networks.
Which statement is correct in this scenario?

The NAT rule with translate the source and destination addresses.

The NAT rule will only translate two addresses at a time.

The NAT rule in applied to the N/A routing instance.

10 packets have been processed by the NAT rule.

NEW QUESTION 66
Your Source NAT implementation uses an address pool that contains multiple IPv4 addresses Your users report that when they establish more than one session with an external application, they are prompted to authenticate multiple times External hosts must not be able to establish sessions with internal network hosts What will solve this problem?

Disable PAT.

Enable destination NAT.

Enable persistent NAT

Enable address persistence.

NEW QUESTION 67
You have designed the firewall filter shown in the exhibit to limit SSH control traffic to yours SRX Series device without affecting other traffic.
Which two statement are true in this scenario? (Choose two.)

The filter should be applied as an output filter on the loopback interface.

Applying the filter will achieve the desired result.

Applying the filter will not achieve the desired result.

The filter should be applied as an input filter on the loopback interface.

NEW QUESTION 68
You are asked to detect domain generation algorithms
Which two steps will accomplish this goal on an SRX Series firewall? (Choose two.)

Define an advanced-anti-malware policy under [edit services].

Attach the security-metadata-streaming policy to a security

Define a security-metadata-streaming policy under [edit

Attach the advanced-anti-malware policy to a security policy.

NEW QUESTION 69
you configured a security policy permitting traffic from the trust zone to the untrust zone but your traffic not hitting the policy.
In this scenario, which cli command allows you to troubleshoot traffic problem using the match criteria?

show security policy-report

show security application-tracking counters

show security match-policies

request security policies check

NEW QUESTION 70
A company wants to paron their physical SRX series firewall into multiple logical units and assign each unit (tenant) to a department within the organization. You are the primary administrator of firewall and a colleague is the administrator for one of the departments.
Which two statements are correct about your colleague? (Choose two)

The colleague can configure the resources allocated and routing protocols

The colleague can access and view the resources of the tenant system.

The colleague can create and assign logical interfaces to the tenant system

The colleague can modify the number of allocated resources for the tenant system

A)company wants to partition their physical SRX series firewall into multiple logical units and assign each unit (tenant) to a department within the organization. You are the primary administrator of the firewall and a colleague is the administrator for one of the departments.
The two statements that are correct about your colleague are:
B) The colleague can access and view the resources of the tenant system. A tenant system is a type of logical system that is created and managed by the primary administrator of the firewall. A tenant system has its own discrete administrative domain, logical interfaces, routing instances, security policies, and other features. The primary administrator can assign a tenant system to a department within the organization and delegate the administration of the tenant system to a colleague. The colleague can access and view the resources of the tenant system, such as the allocated CPU, memory, and bandwidth, and the configured interfaces, zones, and policies1.
C) The colleague can create and assign logical interfaces to the tenant system. A logical interface is a software interface that represents a subset of the physical interface. A logical interface can have its own address, encapsulation, and routing parameters. The primary administrator can allocate a number of logical interfaces to a tenant system and allow the colleague to create and assign logical interfaces to the tenant system. The colleague can configure the logical interfaces with the appropriate address, encapsulation, and routing parameters for the tenant system2.
The other statements are incorrect because:
A) The colleague cannot configure the resources allocated and routing protocols. The resources allocated and routing protocols are configured by the primary administrator of the firewall. The primary administrator can allocate a fixed amount of resources, such as CPU, memory, and bandwidth, to a tenant system and specify the routing protocols that are allowed for the tenant system. The colleague cannot modify the resources allocated or routing protocols for the tenant system1.
D) The colleague cannot modify the number of allocated resources for the tenant system. The number of allocated resources for the tenant system is configured by the primary administrator of the firewall. The primary administrator can allocate a fixed amount of resources, such as CPU, memory, and bandwidth, to a tenant system and monitor the resource usage of the tenant system. The colleague cannot modify the number of allocated resources for the tenant system1.
Reference: Understanding Tenant Systems Understanding Logical Interfaces

NEW QUESTION 71
SRX Series device enrollment with Policy Enforcer fails To debug further, the user issues the following commandshow configuration services security-intelligence url
https://cloudfeeds.argon.juniperaecurity.net/api/manifeat.xml
and receives the following output:
What is the problem in this scenario?

The device is directly enrolled with Juniper ATP Cloud.

The device is already enrolled with Policy Enforcer.

The SRX Series device does not have a valid license.

Junos Space does not have matching schema based on the

NEW QUESTION 72
Which two additional configuration actions are necessary for the third-party feed shown in the exhibit to work properly? (Choose two.)

You must create a dynamic address entry with the IP filter category and the ipfilter_office365 value.

You must create a dynamic address entry with the C&C category and the cc_offic365 value.

You must apply the dynamic address entry in a security policy.

You must apply the dynamic address entry in a security intelligence policy.

NEW QUESTION 73
Click the Exhibit button.

When attempting to enroll an SRX Series device to JATP, you receive the error shown in the exhibit.
What is the cause of the error?

The fxp0 IP address is not routable

The SRX Series device certificate does not match the JATP certificate

The SRX Series device does not have an IP address assigned to the interface that accesses JATP

A firewall is blocking HTTPS on fxp0

NEW QUESTION 74
You issue the command shown in the exhibit.
Which policy will be active for the identified traffic?

Policy p4

Policy p7

Policy p1

Policy p12

NEW QUESTION 75
You are asked to share threat intelligence from your environment with third party tools so that those tools can be identify and block lateral threat propagation from compromised hosts.
Which two steps accomplish this goal? (Choose Two)

Configure application tokens in the SRX Series firewalls to limit who has access

Enable Juniper ATP Cloud to share threat intelligence

Configure application tokens in the Juniper ATP Cloud to limit who has access

Enable SRX Series firewalls to share Threat intelligence with third party tool.

To share threat intelligence from your environment with third party tools, you need to enable Juniper ATP Cloud to share threat intelligence and configure application tokens in the Juniper ATP Cloud to limit who has access. The other options are incorrect because:
A) Configuring application tokens in the SRX Series firewalls is not necessary or sufficient to share threat intelligence with third party tools. Application tokens are used to authenticate and authorize requests to the Juniper ATP Cloud API, which can be used to perform various operations such as submitting files, querying C&C feeds, and managing allowlists and blocklists1. However, to share threat intelligence with third party tools, you need to enable the TAXII service in the Juniper ATP Cloud, which is a different protocol for exchanging threat information2.
D) Enabling SRX Series firewalls to share threat intelligence with third party tools is not possible or supported. SRX Series firewalls can send potentially malicious objects and files to the Juniper ATP Cloud for analysis and receive threat intelligence from the Juniper ATP Cloud to block malicious traffic3.
However, SRX Series firewalls cannot directly share threat intelligence with third party tools. You need to use the Juniper ATP Cloud as the intermediary for threat intelligence sharing. Therefore, the correct answer is B and C. You need to enable Juniper ATP Cloud to share threat intelligence and configure application tokens in the Juniper ATP Cloud to limit who has access.
To do so, you need to perform the following steps:
Enable and configure the TAXII service in the Juniper ATP Cloud. TAXII (Trusted Automated eXchange of Indicator Information) is a protocol for communication over HTTPS of threat information between parties.
STIX (Structured Threat Information eXpression) is a language used for reporting and sharing threat information using TAXII. Juniper ATP Cloud can contribute to STIX reports by sharing the threat intelligence it gathers from file scanning. Juniper ATP Cloud also uses threat information from STIX reports as well as other sources for threat prevention2. To enable and configure the TAXII service, you need to select Configure > Threat Intelligence Sharing in the Juniper ATP Cloud WebUI, move the knob to the right to Enable TAXII, and move the slidebar to designate a file sharing threshold2. Configure application tokens in the Juniper ATP Cloud. Application tokens are used to authenticate and authorize requests to the Juniper ATP Cloud API and the TAXII service. You can create and manage application tokens in the Juniper ATP Cloud WebUI by selecting Configure > Application Tokens. You can specify the name, description, expiration date, and permissions of each token. You can also revoke or delete tokens as needed. You can use the application tokens to limit who has access to your shared threat intelligence by granting or denying permissions to the TAXII service1.
Reference: Threat Intelligence Open API Setup Guide
Configure Threat Intelligence Sharing
About Juniper Advanced Threat Prevention Cloud

NEW QUESTION 76
Exhibit

You are using traceoptions to verify NAT session information on your SRX Series device.
Referring to the exhibit, which two statements are correct? (Choose two.)